JS6430 with unlocking

parameter

model

characteristic

JS6430

Rated output voltage

DC +12V

Output interface location

The six-digit P=7.5mm terminal block is marked NC (normally closed), PUSH, NO (normally open), PUSH, GND, DC+

Output voltage range

Setting error: ±0.5V

Rated output current

3A

Load current range

0.5～3A ( MAX=3A )

Output voltage ripple

Vp-p100Hz<50mV,Vp-pmax<120 mV

Li ; Lo Adjustment rate

Line:±1%；Load:±1%

Comprehensive voltage stabilization accuracy

±3%

Rated output power

36W

Rated working efficiency

≥78% (output power is rated value)

Rated input voltage

Operating voltage: AC176V-264V Rated voltage: AC220V Interface location: Two sections of red power wires are connected to AC-L, AC-N, FG on the PCB board

Rated input current

Rated current: AC0.6A, current range AC0.2～1A

AC input frequency

Rated AC voltage frequency range 47～63Hz, sine wave

Input surge current

The impact current on the power supply grid at the moment of power-on: the maximum value during cold start is 60A/10mS.

Output overload protection

The overload protection point is about 120%-180% of the rated output power; the overload protection is an online power limiting and voltage reduction method; the short circuit protection is an online power limiting method

Unlock function

When PUSH is low level (0V/1S), NO outputs high level +12V, NC output is low level, and returns to normal in 0~30S (counterclockwise extension delay)

When PUSH is high level (+12V/1S), NO outputs high level +12V, NC output is low level, and returns to normal in 0~30S (counterclockwise extension delay)

Power time parameters

Preparation time (SETUP TIME) ≈ 200mS; Stability time (RISE TIME) ≈ 50mS; Holding time (HOLD UP TIME) ≈ 20mS

Electrical strength parameters

Input-output: >AC1.5KV; Input-casing: >AC1.5KV; Output-casing: >AC0.5KV Leakage current <5mA 50Hz 1min.

Operating temperature parameters

The working temperature drift coefficient is about ±0.03[%/℃]; the absolute temperature rise coefficient is about 0.50[℃/W]; when the working output is rated power, the absolute temperature rise of the body is 25℃±5℃

Environmental condition parameters

Storage environment: -20℃～+85℃; 10%～95%RH. Working environment: -10℃～+50℃; 20%～90%RH. (Varies depending on usage environment and power)

Working heat dissipation method

Designed to work continuously, with self-cooling to assist heat dissipation. (Differences in usage environment and installation location affect power usage and lifespan)

Appearance installation dimensions

Specifications and dimensions: L180×W80×H84mm3; wall-mounted installation

Net weight and appearance

The total weight is about 416g; the bottom shell is made of 1.2mm thick aluminum with a sand-oxygen surface treatment in black; the cover shell is 0.5mm thick iron with a black electroplastic surface treatment

Certified safety specifications

National standard GB-8898

Note: 1) The above detection indicators are measured under the following conditions: within the input rated voltage and output rated load range, the environment is 25℃, 85%RH. , when there is no wind around

2) Output DC voltage ripple detection: Use a parallel twisted wire with a length of 30cm and a cross-section of 1mm2 connected to one end of a 0.1μF and 0.47μF capacitor to bypass the detection point and detect 100Hz respectively.

   The maximum peak-to-peak value of the main frequency ripple is Vp-p100Hz and the maximum peak-to-peak value of the comprehensive ripple is Vp-pmax.

    3) Li voltage regulation rate: when the load is at the rated value, the input voltage changes within the rated range; Lo load regulation rate: when the input is at the rated voltage value, the load changes from zero to the rated value.